Deck Grip – Clear Indoor & Outdoor Non-Slip Sealer for Concrete

$345.00

Description

DESCRIPTION

Deck Grip is an anti-slip sealer for concrete and other stone surfaces. This versatile non-slip coating is non-yellowing, water-based acrylic and is easy to apply. Deck Grip non-slip concrete results in a clear, semi-gloss and barefoot-friendly finish that is chemical resistant, UV resistant and highly durable. Deck Grip is the perfect anti-slip solution to treat slippery pool decks, and all types of stamped (sealed or unsealed) concrete decks.  Compatible on virtually all types of natural stone surfaces where anti-slip sealers are desired.

Sealed Stamped Concrete – Deck Grip will work great on top of all sealers and is chemical and chlorine resistant.  Ideas for surfaces surrounding pools and spas.  Please start with a clean dry surface prior to application.  Allow 24 hours to cure.  Apply 2 thin coats for best durability and slip resistance.

Even when wet, your slippery floor’s slip resistance after the non-slip solution will surpass ANSI A137.1, A326.3 or B101.3 standards.

0.52 Wet DCOF – ANSI B101.3
0.53 Wet DCOF – ANSI A137.1 / A326.3
0.62 Wet SCOF – ANSI B101.1

PRODUCT FEATURES

  • Great for bare feet
  • Use it on pool decks and sealed concrete
  • One 3/8” nap roller included per gallon
  • Deck Grip is available in 1 gallon and 5-gallon pails
  • Can be used indoors or outdoors
  • It dries clear with a semi-gloss finish and is easy to apply
  • One gallon covers 300 – 600 square feet

SPECIFICATIONS

Gallon 5-Gallon
Coverage per Sq Ft 300-600 Appx 2,500
Cost per Sq Ft (Appx.) $0.25 $0.23
⅜” Nap Rollers Included 1 5
Volume (liters) 3.78 18.92

Safety Precautions:
• Use in a well-ventilated area.
• If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Hotline at 1-800-424-LEAD or www.epa.gov/leadfor more information.

Optional Safety Equipment:
• Chemical-resistant gloves
• Eye protection
• Mask

Surface Preparation:
• Surface preparation varies by surface. Please see chart below for specific surface preparation instructions.

Application Instructions:

Step 1: Mixing Additive: The quantity of SlipDoctors Deck Grip Additive to be used depends on the level of slip resistance desired(see chart below). Maximum texture is recommended for the most effective anti-slip protection. Pour desired amount of Additive into Deck Grip container and gently mix to ensure even distribution. Avoid shaking to prevent foaming. Mix occasionally during application.

Step 2: TEST: Deck Grip should be tested on a small inconspicuous area before full application

Step 3: Deck Grip can be rolled or sprayed, rolling is recommended. Roll: Use the included3/8” nap roller to evenly coat the surface. Avoid puddling in low areas. If puddles occur, roll them out. Two thin coats are recommended rather than one thick coat. Spray: Spray using a 5916 nozzle that produces a flow of 1/10 of one gallon per minute. Spray in a fine fog pattern without spurts or dribbles to form a thin continuous film. Avoid puddling in low areas. If puddles occur, roll them out.

Step 4: For added protection, greater performance and durability,we recommend applying Deck Gripin two thin coats. Allow first coat to dry for 2-4hours before applying the second coat. The second coat should be applied at a right angle to the first coat.

Step 5: Clean-up:While Deck Gripis still wet, equipment may be cleaned with soap and water. Once dried, equipment may be cleaned with a solvent, such as xylene or toluene.

Maintenance:
For general cleaning and maintenance,use a light pressure rinsing. For best results to remove oily deposits or other foreign matter, apply pH-neutral cleanerat recommended dilution rate and scrub lightly with a soft bristle deck brush.Do not use alcohol-based cleaners, such as pine-sol.

Reviews

There are no reviews yet.

Be the first to review “Deck Grip – Clear Indoor & Outdoor Non-Slip Sealer for Concrete”

Your email address will not be published.